Bionicdodge.Com
Welcome, Guest. Please login or register.
June 26, 2017, 05:25:04 PM

Login with username, password and session length
Search:     Advanced search
   

94652 Posts in 11565 Topics by 2093 Members
Latest Member: Dodgey2
* Home Help Search Gallery Calendar Login Register
Bionicdodge.Com  |  Bionic Tech  |  Street Tires, Suspension & Chassis (Moderators: donram360, adamsredlines)  |  Topic: Wheel Bearing Hubs: You Get What You Pay For 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Wheel Bearing Hubs: You Get What You Pay For  (Read 481 times)
98Dak408
Site Donor
Administrator
Bionic Wh0re!
*****
Offline Offline

Posts: 5042



WWW
« on: October 30, 2016, 04:03:18 AM »

I did a front pad and rotor swap on my '90 Dakota 4X4 the other day and realized the front wheel bearings were shot.  Since I don't expect to get a few more months out of this high mileage Michigan truck, as it is deteriorating every year and I am reluctant to put too much money into it, I bought cheap Chinese bearing hubs from Rockauto for less than half the price of the regular ones.  They installed fine but when trying to install the dust caps I wasn't able to install either side.  The driver's side ID for the dust cap was too small and the passenger's side ID for the dust cap was too large.  Poor machining quality control.  I didn't feel like pulling everything apart again...and screw around trying to ship them back, etc.  Since I drive this truck day-by-day on a kiss-and-a-promiise basis, I left the dust caps off.  If I get another two months out of this truck I will be happy. Nevertheless, you do tend to get what you pay for.   
Logged

1998 Dakota  R/T CC; 408 Stroker; Comp 220/230, SCT; Ported Eddy’s; M1; HiPoTek 53.6 mm TB; MP Headers; Single 3 1/2" Exhaust; Transgo; PATC 2800; Motive 4.56; Auburn LSD; Hotchkis TVS - 2/3 Drop; Sidewinder Customs 13" Viper Brakes; HiPoTek X-Brace, Driveshaft Loops, Engine Torque Strap, and Differential Cover.



Thank you for looking, Richard
dakman
Bionic Junior
*
Offline Offline

Posts: 144


« Reply #1 on: October 30, 2016, 07:36:30 AM »

So true.
Logged
Richie
Global Moderator
Bionic Master
***
Offline Offline

Posts: 2128



« Reply #2 on: October 30, 2016, 01:57:49 PM »

Oh yea you no that is true.
Logged

Big a** supercharged 4.7L HO, cammed, Custom made Supercharger COG drive system, 72mm F&B throttle body, ROSS ceramic coated pistons, Billet H beam rods, 1st set of race prepped big valves heads W/ behive springs, Custom one off sheet metal intake, Modified Edelbrock Mustang intake elbow, ATI super dampner, 3,000 Edge racing billet stall converter, meth injected, SCT tuned, 60# injectors, Aeromotive Eliminator fuel pump, Aeromotive -12 Fuel Filter, Boost reference FPR, Custom fuel cell, Braided stainless line and AN fittings, Aeromotive Billet fuel controller,  2 bar map, Turbo Smart Race Port BOV, 180d* T stat, True dual exhuast, Built tranny W/ deep trans pan, built transfer case, 275 60 R17 rubber.
donram360
Global Moderator
Bionic Supremacist
****
Offline Offline

Posts: 2661


« Reply #3 on: October 30, 2016, 02:43:33 PM »

at least you went into it not expecting much....
I had to replace my inner and outer bearings and races (been a while since I had to knock out a set of races from a rotor) on my 92 2wd a few days ago as it was just starting to howl.... pass side outer bearing rollers were pitted just on 1/2 the roller, the 1/2 towards the small end of the taper. When I pulled them and put them into the solvent tank to clean and inspect, I could barely but faintly read "CHINA" on the inner race, so being a '92 truck, I know the bearings that I removed weren't originals.   
I asked for name brand at the parts store, I got "National" which has been around forever. and on the box label? made in china... not happy.
Logged
magnumman
Site Owner
Bionic Supremacist
****
Offline Offline

Posts: 3642



WWW
« Reply #4 on: October 30, 2016, 05:20:54 PM »

Suran wrap and a rubber band will hold the grease in, haha.  Well it works for a beer I want to save for later.
Logged

2001 Ram QC 1500: 360cid, 2wd, K+N CAI, SCT tune, Autolite AP3923\'s, MP 1.7 rollers, MP pushrods, SST rims, Hypertech coil, 10.2mm wires, Gibson super truck exhaust, 3\" magnaflow cat, modified Y pipe, modified kegger, 3.92 LSD, MSD-6, Transgo shift kit, 4.7L Injectors, Hipotek 52mm TB, (Currently under construction for a 408 build)

POS Chevy Trailblazer 4x4, the 4x4 is the only good part. This thing is a turd.
Bionicdodge.Com
Advertisement
Thanks to the following sponsor
   

 Logged
Pages: [1] Go Up Print 
Bionicdodge.Com  |  Bionic Tech  |  Street Tires, Suspension & Chassis (Moderators: donram360, adamsredlines)  |  Topic: Wheel Bearing Hubs: You Get What You Pay For « previous next »
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.11 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!